Roman Orbital Hinged Bath Screen

Bathroom Suites Toilets Sinks Shower Enclosures Heated Towel Rails Bathroom Taps Bath Screens Bathroom Furniture Shower Trays Baths Showers Mirrors and Cabinets Accessories & Seats Clearance

Back to Results

Fitting instructions for the Roman Orbital Hinged Bath Screen

IMPORTANT PRE-INSTALL CHECKS

1. Check you have the correct hand bath screen. Please look at the labels on the side of the product packaging and use the illustrations below.
2. Check all the product components are in the box and the fixing kits are complete. Please check this with the component check list overleaf.
3. Un Pack your product and handle it with care.
4. Please check the product for defects or damage. Once the installation has commenced cannot accept responsibility for any defects or damage to the products.
5. Please take the time to read these instructions prior to installing your product.
6. Before you commence any drilling check there are no hidden electrical cables and/or water pipes in the walls.
7. No attempt should be made to re-work the toughened safety glass.
8. The installation should be performed by two persons.
9. It is strongly recommended the walls the product is going to be installed on are vertical. However the wall profiles have 25mm of adjustment to help compensate for some deviation.
10. It is strongly recommended the product is fitted on tiled surface or similar waterproof surface.
11. It is strongly recommended the walls are tiled and grouted after the installation of the bath and before the installation of the product. This will provide maximum adjustment and help when sealing the product.
12. If the walls and/or the bath are not level you will not achieve maximum adjustment of the product.
13. Pictures used are for illustration purposes only, product designs may alter slightly as a result of continuing product development.
14 We do not stipulate where the European Standard Kite Mark should be positioned on the glass panels when being factory assembled.

Step 1: IMPORTANT PRE-INSTALLATION CHECKS

1 Check the bath is level, on all sides (The bubble should be in the centre of the two lines on the spirit level).
2. Stand in the bath and check there is no adverse movement.
3. The walls should be tiled and grouted up to the bath.
4. The tiles and the bath should be sealed with the bath full of water, using bathroom sealant.

• Spray the seal and joints with the shower head and check for leaks when the silicone has cured.
• Check the plumbing for leaks.
• Do not Plasterboard over the bath.
• Do not grout the tiles when the enclosure has been fitted as the grout may discolour the aluminum profiles.
• When all of the above criteria is met please proceed to the next step in these instructions.

Step 2: FIXING THE WALL PROFILE

1. Position the wall profile 5mm from the inside edge of the bath. Take this measurement from the inside wall of the profile. The lip of the profile faces towards the inside of the inside of the bath.
2. Mark the locations for the drill holes using a pencil.
3. Drill the holes using 6mm masonry bit (not supplied). Then push the wall plugs in beyond the depth of the tile.
4. Apply sealant where the bottom of the wall profile will meet the bath and tiled wall.
5. Fix the Wall Profile using the 40 mm screws (supplied).
6. Apply Sealant to the inside of the wall profile where it meets the bath.

• The wall profiles must be vertically level. (The bubble should be in the centre of the two lines on the spirit level).

Step 3 - Locating and Fixing the Bath Screen

1. Offer the Bath Screen into location on the bath and in the wall profile.
2. Check the gap between the glass and the bath is parallel; along the full length of the glass.
3. Drill through the pre-drilled holes of the wall profile using the 3mm drill bit.
4. Fix the Screen into wall profile using the supplied 16mm pan head screws.
5. Run a bead of sealant down the length of the bath top seal.
6. Position the bath top seal on the bath, so it locates against the profile of the Screen and runs parallel with edge of the bath. (Make sure the fall of the strip faces the inside of the bath).
7. Tape the bath top seal on the bath using a low tack tape positioned at each end, and in the centre of the Strip.

• (You may need help to hold the screen in location while you drill and fix the screen to the wall profile).
• (Clean away the excess silicone from the bath).
• (Please leave the sealant 24 hrs to cure before use)

Step 4 - Assemble the Bottom Seal Extrusion

1. Take the Bottom Seal extrusion and apply a thin bead of silicone down both internal walls.
2. Make sure the deflector strip is on the inside of the Screen and push the extrusion onto the glass. Hold for a few moments.
3. Use some Low tack tape to hold the Bottom Seal Extrusion in position. Use a strip at each end and one in the centre, leave for a minimum of two hours to cure.
4. Close the bath screen. • (Clean away the excess silicone from the screen).

• (Please leave the sealant 24 hrs to cure before use).

Step 5 - Fix the Cover Caps and Seal the Screen

1. Clip on the wall profile cover trim. (It is designed to be a tight fit so take care).
2. Place all the cover caps on the profiles. (R and L on the inside of the caps indicate the handing of the caps looking from the inside of the enclosure).
3. Stick on the Branding Badge (if applicable).
4. Seal vertically the full length of the wall profiles on the inside and outside of the enclosure where it meets the tiles.
5. Seal horizontally along the bottom of the vertical Profiles on the outside of the bath screen where it meets the bath and tiles.

• (Please leave the sealant 24 hrs to cure before use).

There are currently no reviews on this product.
Click here to write a review.