Fitting instructions for the Roman Embrace Sliding Shower Door 1000mm

Consumer Guarantee

Please make sure you complete and return the Guarantee card which is enclosed with this product. Failure to validate the Guarantee will mean only the 1 Year Statutory Guarantee will apply.

Some Important Information to read before you install your product.

1. Check you have the correct product. Please look at the labels on the side of the product packaging.

2. Check all the product components are in the box and the fixing kits are complete.
Please check this with the component check list below.

3. Unpack your product and handle it with care.

4. Please check the product for defects or damage. Once the installation has commenced we cannot accept responsibility for any defects or damage to the products.

5. Please take the time to read these instructions prior to installing your product.

6. Before you commence any drilling check there are no hidden electrical cables and/or water pipes in the walls.

7. No attempt should be made to rework the toughened safety glass.

8. The installation of the product should be performed by two persons.

9. It is strongly recommended that the walls the product is going to be installed on are vertical.

10. It is strongly recommended the product is fitted on tiled surface or similar waterproof surface.

11. It is strongly recommended the walls are tiled and grouted before the product is installed.

12. If the walls and/or the tray are not level you will not achieve maximum adjustment of the product.

13. Pictures used are for illustration purposes only, product designs may alter slightly as a result of continuing product development.

14. We do not stipulate where the European Standard Kite Mark should be positioned on the glass panels when being factory assembled.

What's in the box:

No4 x ¼” pan head screws - 6
40 mm Screws (wall profiles) - 6
Wall Plugs - 6
2.5mm drill bit - 1
Profile Cover Caps - 2
Branding Badge - 1
Allen Key 4mm -1

The sliding door is designed to fit into an alcove between two tiled walls (Diagram A) or with an inline or side panel.

SPARE PARTS: If you need to replace any damaged parts please see illustration below for parts list then call Customer Relations on 01325 328033/328034

	TROUBLE SHOOTING GUIDE.
Problem	Solution
LEAKING	. Check the Tray has been sealed correctly prior to installation of the enclosure Step 1. . Check the inside gap has been sealed correctly between the tray and wall profiles Steps 2 & 5. . Check that the base of the enclosure is sealed to the tray top from the outside only Step 7. . Check that a bead of silicon the width of the wall profile has been applied Steps 2 & 5. . Check to see if both wall profiles have been sealed vertically inside and outside where they meet the tiled wall Step 7. 6. Check that the base of the enclosure hasn’t been sealed to the tray top on the inside of the cubicle. Important: This enclosure should be water tested conforming to BS EN 14428
ENCLOSURE	1. Check that the enclosure has been fitted onto a tiled wall or a similar sealed surface.
ALIGNMENT ON THE TRAY OR FLOOR	2. Check that the wall profiles have been fitted 15mm in from the front outside edge of the tray Steps 2 & 3.
	3. Check that the wall profiles have been fitted completely vertical (the bubble must be in the centre of the two lines on a spirit level) Steps 2 & 3. 4. Check that the enclosure is completely vertical and level.
DOOR NOT OPERATING / CLOSING CORRECTLY	1. Check that the tray is completely level (the bubble must be in the centre of the two lines on a spirit level), this could have an effect on the positioning of the door when adjusted, you might not have enough adjustment within the wall profile due to compensating for an out of level tray Step 1. 2. Check that the wall profiles are completely vertical (the bubble must be in the centre of the two
	lines on a spirit level) Steps 2 & 3.
	3. Check that the channels which the doors slide in has got some silicon lubrication gel in. (If not,
	please apply some form of lubrication agent in the channels).
	4. If the door does not hang vertically, you have further adjustment at the top of each wheel assembly.
	Using the Allen key (supplied) turn the adjustment screw. Turning the adjustment screw clockwise
	will lift the door, and turning the adjustment screw anti clockwise will lower the door Step 6.

There are currently no reviews on this product.
Click here to write a review.